Props off, quad disarmed, battery in. Use a LiPo for this test unless you know that your flight controller powers CAMLINK and the video system from USB. Fresh from the install the LED sits solid amber: powered, but not ready.
Watch the stepsPauseContinueWatch againLoading the walkthrough…The walkthrough could not load. Reload the page to try again.{current}/{total}Place the four OSD linesShow free card spaceKeep recording while you recoverRecognize overheatingRecognize a cold warningThe OSD stays empty until placement is verified. Then it shows the Setup Mode information.Add free card space to line 4 and see the result.Keep the recommended five-second delay. See how disarming after a crash and re-arming before it ends preserves the same recording.See the warning when a GoPro, DJI or Insta360 reports overheating.See the cold warning reported by a GoPro, including Mission 1 Pro.Once your phone is connected to CAMLINK’s Wi-Fi, open 10.0.0.1 to reach this screen.Open Before You Fly to check the connection to Betaflight.Open CAMLINK lines to choose where the four lines will appear.Under Corner, choose Bottom left.Choose Set up to prepare the four lines for Betaflight.Choose Confirm setup to enable and place all four lines in Betaflight.Verified. The four Setup Mode lines now appear at the bottom left.Let’s show free card space beside the camera name.Open OSD to choose which information appears on each line.Select line 4 to change the information beside the camera name.Double-tap ASPECT to remove the aspect ratio and make room.Add SD card to show the remaining card space; the change saves automatically.Line 4 now shows M1P and 108G: Mission 1 Pro with 108 GB free on its card.Stop delay gives you time to recover after a crash without ending the clip immediately.Open Recording to find Stop delay.Keep Stop delay at the recommended 5 seconds. You can adjust it from 0–30 seconds.Disarming starts the countdown. Re-arm before it ends and CAMLINK cancels the pending stop, so the same clip continues.Heads-up warnings are on by default, so the goggles show overheating when your camera reports it.Heads-up warnings are on by default, so the goggles show it when your GoPro reports that it is too cold.Open Warnings to set the two thresholds and the Heads-up switch.Leave Heads-up warnings on; each one appears only when the camera reports that condition.The camera reports overheating while recording may continue. Check REC as well; the temperature message adds context if the clip stops.The GoPro reports that it is too cold. Check the camera when a recording will not start.The camera confirms recording. The same clip continues while you recover.Disarmed. Stop delay is counting down while the camera keeps recording.The camera confirms that recording stopped. Check this before unplugging power.Start recording on armKeep Auto record on arm on to start recording when you arm. Turn it off if you want to start each clip yourself.Keep recording after disarmKeep Auto stop on disarm on for normal flights. Turn it off to keep recording after disarming, for example after a crash. You must then stop the clip yourself.Stop delay: time to re-armWe recommend 5 seconds, adjustable from 0–30. After a crash, disarm and re-arm before the countdown ends to keep one continuous clip. Wait for a confirmed stop before unplugging power.Choose what starts recordingArm is the factory setting and our recommendation for normal flights. Combi is our preferred option when you also want to stop and restart takes with a momentary radio button.Choose the recording channelKeep your radio on and connected to the quad. Move the recording switch or button, then select the AUX channel that moves with it.Choose the record positionLow, Mid or High tells CAMLINK which channel position means record. In Switch mode, leaving that position asks the camera to stop immediately.Choose the battery warning pointChoose when the camera-battery heads-up appears, from 5 to 30 percent. A higher percentage warns earlier. A percentage is not a promised recording duration.Choose the recording-time warning pointChoose how many minutes should still fit on the camera's storage when the heads-up appears, from 1 to 30. This is recording capacity at the current settings, not battery runtime.Match AUX bands to your radioUsually leave Custom AUX bands off. These shared boundaries affect recording, preset, HiLight and the Camera 2 channel together. Enable them only when your radio's values do not fit the default ranges.Set where Low startsLow start sets the lower edge of the shared Low range. It affects every CAMLINK function using that range, not just one channel.Set where Low endsLow end sets the upper edge of the shared Low range. The editor keeps the ranges ordered when a boundary moves.Set where Mid startsMid start sets the lower edge of the shared Mid range. Match it to your radio only if the default range does not work; the change applies to all CAMLINK radio controls.Set where Mid endsMid end sets the upper edge of the shared Mid range. Keep the centre switch position inside it; other CAMLINK functions use the same boundary.Set where High startsHigh start sets the lower edge of the shared High range. For GoPro preset switching, values outside all ranges also count as High.Set where High endsHigh end sets the upper edge of the shared High range. Adjust it only if needed for the values your radio sends.Choose whether GoPro wakes automaticallyAuto wake is on by default. Turn it off when you want the GoPro to stay off while the quad remains powered; switch the camera on yourself when you are ready.Change GoPro presets from the radioPrepare presets on your GoPro, then select them from your radio. Change camera settings in flight without landing to touch the camera.Mark a moment in your GoPro clipMark a moment in a GoPro clip with a momentary radio button. The same clip keeps recording. Your viewing or editing software must support HiLight markers to use them later.Set a naked GoPro’s clock from GPSUseful when your GoPro does not retain the correct date and time, especially in a naked build. GPS time sync needs a valid fix from the flight controller and your timezone offset. It is not timecode synchronization.Choose the GoPro preset channelSelect the AUX channel used by your preset switch. It may share a channel with the recording trigger.Choose whether a preset change splits the clipIgnore keeps the current clip uninterrupted and loads the new preset after recording stops. Apply and restart stops the clip, loads the preset and starts a new clip if recording is still requested.Choose the HiLight channelChoose the AUX channel sent by your HiLight button. Keep it separate from the recording and preset-switch channels to avoid conflicting commands.Choose the HiLight press positionPress position tells CAMLINK which AUX position counts as a HiLight press. Match Low, Mid or High to the position your radio button sends.Set the local time for your clipsWith GPS time sync enabled, tap Use my timezone. It takes the current UTC offset from your phone or computer. Check it again after travel to another timezone or a daylight-saving change; manual adjustment is available in 15-minute steps.Recognize your CAMLINK Wi-FiNetwork name lets you personalize the Setup Wi-Fi. You do not need to rename it: the default CAMLINK name already has a unique device ID. Tap Save Wi-Fi if you change it.Choose the Setup Wi-Fi passwordChange Password if you want your own Setup Wi-Fi password. This is optional and does not change camera pairing. Tap Save Wi-Fi; network changes apply after restarting CAMLINK.RX/TX wiringLeave RX/TX wiring on Auto. CAMLINK works out which wire is TX and which is RX by itself. Normal and Swapped set the direction by hand.Set the LED for day or nightNight, Dim and Day change the status LED brightness. Dimmer settings also dim warning colors; the LED cannot be switched off.Choose what line 1 showsLine 1 normally holds the state and recording timer. Add or move fields as needed; warnings alternate with this line, and content beyond 16 characters can be cut off.Choose what line 2 showsLine 2 normally holds camera battery and remaining recording time. Adding free space makes a custom layout; watch the 16-character limit.Choose what line 3 showsLine 3 normally holds resolution, frame rate and profile when the camera reports them. You can add free space or move fields; information the camera does not provide stays blank.Choose what line 4 showsLine 4 normally holds the camera tag and aspect ratio. Replace a field with SD card to see available storage beside the camera name. With Camera 2 on, its token starts at line 4 unless you move it.Insert a card or check that the camera recognizes it. GoPro, Osmo Nano, Action 2, Blackmagic, Sony and Insta360 report this warning. On Nano, CAMLINK first waits for the change to internal storage to finish.The camera reports that its recording storage is full. Make room or replace the card before flying. This warning is available across supported camera families.GoPro, Blackmagic and Insta360 can report a card write or format error. Check the card in the camera. This warning is always on.The camera reports overheating. REC can still be visible, so check recording separately. If the clip stops, this temperature report helps you check the camera's cooling and mount.The GoPro reports that it is too cold. Check the camera when a recording will not start. Other camera families do not provide this warning.The camera battery reached your threshold. This example shows 8%. The heads-up stays quiet while the battery value is on your OSD.GoPro, DJI, Sony and Insta360 can report photo, timelapse or another mode outside normal video. Select video on the camera. Displayed video settings can still describe a saved video preset; they do not prove that video mode is active.The camera has two minutes of recording space left at its current settings. The heads-up stays quiet while the SD card value is on your OSD.A request to start recording failed. Check the camera before flying. This message appears automatically; a failed request is never shown as a successful recording.Press button 1 to pair a camera. Hold button 2 for 3 seconds to open Setup Mode.CAMLINK is looking for the saved camera. The displayed camera name identifies that target; the connection is not ready yet.CAMLINK has found the target and is establishing the connection. Camera readings appear after the camera supplies current status.Put the new camera in pairing mode, then press button 1. The saved camera is replaced only after the new pairing succeeds.Follow the pairing steps for your camera, then press button 1 to try again. A failed attempt does not replace the saved camera.The camera no longer accepts the saved pairing. In Setup Mode, open Cameras and remove it. Leave Setup Mode, then follow the camera's pairing steps again.CAMLINK tried to wake the GoPro but received no answer. Check the camera. Press its button only when you know it is asleep.CAMLINK could not start Bluetooth. Press either board button to restart it.Short-press button 2 to disconnect the Bluetooth camera link, stop searching and hide the four CAMLINK lines. Your flight data and saved pairing remain. Press again to reconnect.Choose what you want to learn.Open {page}.Set {label} to {value}.Saved in this example. {meaning}This shows the controls you use on your own CAMLINK. No device is changed here.{meaning}Open {page}.Set {label} to {value}.Saved.{meaning}Open {page}.On your own CAMLINK, these controls perform the action shown. Here, you can inspect them without changing a device.{meaning}Move a field to another line and see where it appears in your goggles.Open OSD to rearrange the four lines.Hold a field, then drag it to its new position. On a computer, drag it directly.The field is now on its new line. The layout saves automatically; keep each line within 16 characters.Assign 25FPS to Low for normal-speed B-roll.Assign 200FPS to Mid for slow motion.High is optional. This example assigns CUSTOM as a third prepared preset.Choose Use my timezone to fill in your browser’s current timezone offset.Assign the shots you want to your switchPrepare 25 fps B-roll and supported 200 fps slow-motion presets, then assign them to Low and Mid. High is optional. Check shutter, ISO and your fitted ND filter for each preset before flying.Find firmware updatesUpdate when a release adds a feature you need or fixes a problem you have. Download the package, then open Firmware Update on your CAMLINK to install it.See what factory reset removesFactory Reset removes both paired cameras, saved GoPro presets, settings, Wi-Fi credentials and the diagnostics record. The real device then comes back in Setup Mode on its default Wi-Fi and shows whether the reset completed.Restart CAMLINKReboot restarts CAMLINK in Flight Mode and ends the Setup Wi-Fi connection. Saved settings remain; hold button 2 for three seconds to return to Setup Mode.Download a file for supportOpen Device, then Diagnostics, and choose Download diagnostics file. Attach the file from your CAMLINK to an email to info@itsfpv.net with a description of the problem.Manage your camerasThe Cameras page shows Camera 1 and Camera 2 and lets you remove either one. To pair, leave Setup Mode: press button 1 for Camera 1, or hold it for 3 seconds for Camera 2.Use your phone’s timezoneEnable GPS time sync, then tap Use my timezone to use your phone or computer's current UTC offset. Repeat after a timezone or daylight-saving change so your clips keep the correct local date and time.Choose your recording controlKeep Arm for automatic flight recording. Choose Switch for a separate recording switch, or Combi for a momentary button plus arm/disarm automation.Compare the three OSD layoutsUse the OSD to plan ahead on the way back: check camera battery, recording capacity and your next shot. Clean keeps the essentials; Standard and Detailed add format and camera details. Unsupported values stay blank.Off leaves recording to the camera. CAMLINK still shows its status in the goggles.Arm is the factory setting and the simplest recommendation: arming requests recording, disarming starts the stop delay.Switch gives recording its own radio switch. The selected position records; moving out of it requests an immediate stop, independently of arming.Button uses a momentary radio button. Press to start, release, then press again to stop a take. These direct stop commands skip Stop delay.Combi is our pick for manual takes in flight: recording starts with arming, and a momentary button lets you stop and start again. Disarming still starts the stop delay.Clean shows state, timer, camera battery and recording time left. Lines 3 and 4 stay empty.Standard adds resolution, frame rate and profile on line 3 when the camera supplies them. Line 4 stays empty.Detailed adds the camera tag and aspect ratio on line 4. This is CAMLINK’s factory layout.What would you like to set up?Move an OSD fieldMove a field and see where it appears in your goggles.CAMLINK set the GoPro clock and read it back successfully. The confirmed time appears on line 2. This sets date and time; it is not frame-accurate timecode or synchronization between cameras.CAMLINK could not verify the GoPro's clock. Check GPS time sync and the flight controller's GPS fix. This message does not mean that recording failed.The GoPro confirmed the selected preset. Its reported settings now appear in your configured OSD fields.The requested GoPro preset was not confirmed. The old preset may still be active. Check the camera before relying on the new settings.Assign a GoPro preset to this Low, Mid or High position in Setup Mode. An empty position cannot load a preset.The GoPro confirmed the bookmark. The same clip keeps recording. It can help you find the moment later if your viewing or editing tool supports GoPro HiLight markers.The GoPro did not confirm a HiLight marker. A second line may explain why, such as no recording being active. This does not mean an ongoing recording has stopped.Blinking RECWith Blinking REC on, REC in the goggles blinks once a second while the camera records. It is off by default.Switch Camera 2 onOpen Cameras and switch Camera 2 on. To pair it, leave Setup Mode, put the second camera in pairing mode and hold button 1 for three seconds until the goggles show PAIR CAMERA 2. Switching Camera 2 off keeps its pairing.Choose how Camera 2 recordsShared follows Camera 1's start and stop, including its stop delay. Independent records while its own AUX switch sits in the record position and stops right away when the switch leaves it.Choose the Camera 2 switchWith Independent, pick the AUX channel for Camera 2 in the Camera 2 channel screen. It cannot share a channel with the Camera 1 recording trigger, the preset switch or HiLight.Choose the Camera 2 record positionPick the switch position that records on Camera 2. Leaving that position stops Camera 2 without a delay.Blinking 2:RECWith Blinking 2:REC on, 2:REC in the goggles blinks once a second while Camera 2 records. It is off by default.Turn the heads-up warnings on or offHeads-up warnings cover camera battery, SD low, hot and cold. They are on by default and show once when they appear and once when you arm. Switched off, those four stay silent; card, mode and recording warnings still show.Beep with the droneWhile the quad is disarmed and no recording is wanted, the GoPro beeps when the quad's beeper switch is on or its radio link is lost. It is on by default and works for a GoPro as Camera 1.Remove Camera 2Cameras shows the paired Camera 2 with its own Remove button. Removing it leaves Camera 1 paired. It is refused while Camera 2 records.Setup ModeSet the connection, radio bands and LED, then find the tools for maintaining your CAMLINK.Read the LED in any lightKeep the same status color and choose how bright it should be.Personalize the Setup Wi-FiRenaming the network is optional. Its default CAMLINK name already includes a unique device ID; change it only if you prefer your own name.Troubleshoot the Betaflight connectionCheck the flight-controller link. The baud rate is fixed at 115200, and RX/TX wiring on Auto finds the direction by itself.AUX ranges: advanced radio settingsThe default Low, Mid and High ranges normally work. Adjust them only when your radio's values do not fit those ranges.Custom AUX bands changes the global meaning of Low, Mid and High for CAMLINK's radio controls. This example edits one boundary; the other boundaries work the same way.Manage your CAMLINKFind your paired cameras, the support file and the maintenance screens; real device actions stay on your CAMLINK.OSDCheck camera battery, recording space and the selected shot while flying back, so you know what needs attention before the next take.Start with a layoutKeep the camera information you actually use. Every layout includes state, timer, battery and recording time left; the fuller layouts add format and camera details for checking the next shot.Customize the OSDPut the information you use on the OSD. The preset name helps you check the selected shot without landing to look at the camera.WarningsSee each message, understand its meaning and recognize when the camera needs attention.Set when the heads-up warnings appearTwo numbers decide when the camera battery and the recording time count as low. One switch turns the four heads-up warnings on or off. Card, mode and recording warnings always show.Warn before the camera battery runs outWarn before recording space runs outMissing card or no recording spaceWarnings for a missing, full or faulty card always show. Set when the recording-time heads-up appears.Warn when the memory card is missingWarn when recording storage is fullWhen the camera reports a card errorKnow when the camera is too hot or coldThe camera can report a temperature problem while still recording. Check the recording state in the OSD too.Warn when the camera gets too hotWarn when the GoPro is too coldCheck what recording needsRecognize a non-video mode before you fly.Warn when the camera is not in video modeCheck Sony recording controlsThe Sony is linked but not set up for remote recording, so the state word reads CHK. Turn on Bluetooth Rmt Ctrl and set the MOVIE button to movie recording.If recording does not start or stopCheck whether the command failed or the camera has not confirmed its recording state.When recording fails to startWhen the camera has not confirmed the startThe camera has not confirmed the requested start. It may be recording. Check the camera; a missing confirmation does not mean it stopped.When the camera stops on its ownThe camera stopped recording on its own while you still wanted it to record, for example while armed. CAMLINK is asking it to record again. Check the camera.When recording does not stopCAMLINK sent a stop, but the camera has not confirmed it. Assume the camera is still recording and check it when you land.Understand the connectionFollow pairing and the search screen, then see which messages ask you to act.When no camera is paired yetPair a different cameraWhen the camera asks for approvalSome cameras ask before they pair. The goggles show CONFIRM with ACCEPT ON CAM, or CODE and a number to compare on a DJI. Approve on the camera.When camera pairing failsWhen pairing is declined on the cameraThe pairing was declined on the GO Ultra, so nothing is saved. Press button 1 when you are ready to try again.Pair Camera 2With Camera 2 switched on, hold button 1 for three seconds. The goggles show PAIR CAMERA 2 and the light blinks magenta, very fast.When Camera 2 pairing failsCamera 2 pairing did not finish. Hold button 1 for three seconds to try again.Pair the camera againWhen CAMLINK is looking for its cameraWhile the camera connection is being madeWhen the camera drops outThe camera had answered and then dropped out. The goggles show the search screen and the light blinks fast amber until the camera is back.When the camera is off or asleepThe camera reports that it is off or asleep, the state word reads OFF and the light is solid amber. Switch it on. A GoPro shows this while Auto wake is off. CAMLINK cannot wake an Osmo Nano.When the GoPro does not wake automaticallyWhen a DJI camera stops answeringThe camera stopped answering and reconnecting cannot bring it back. Switch it off and on.When the flight controller does not answerNo answer from the flight controller for 10 seconds while a feature needs one, such as recording on arm or on a switch. Seeing it in the goggles means CAMLINK still reaches the flight controller, so check the wire from the flight controller TX pad to CAMLINK RX.When CAMLINK needs a restartFly without an action cameraKnow what the GoPro confirmedRead the success and failure messages for clock sync, presets and HiLight markers.When the GoPro clock is synchronizedWhen the GoPro clock cannot be verifiedWhen a GoPro preset has been appliedWhen a GoPro preset change failsWhen a switch position has no presetWhen a moment has been marked in the clipWhen a clip marker could not be savedRecording controlRecord each flight automatically or from your radio, and choose how Camera 2 follows.Choose how you control recordingStart with Arm for automatic recording. Combi adds a momentary radio button for stopping and starting takes in flight.Start with the flightLeave automatic starting on so each flight begins with a recording. Turn it off only when you want to choose the start yourself.Stop delay: time to re-armFive seconds gives you time to disarm after a crash and re-arm without splitting the recording. Re-arming before the countdown ends keeps the same clip running.Keep recording while you recoverKeep the recommended five-second delay. See how disarming after a crash and re-arming before it ends preserves the same recording.Choose the radio inputTurn your radio on and connect it to the quad. Move the switch to see the live AUX input reaching CAMLINK, then choose its channel and recording position.Assign your recording switchMove the switch to find its AUX channel, select it, check the movement again and choose the position that should record.Make REC blink in the gogglesBlinking REC is off by default. Switch it on and REC blinks once a second while the camera records.Fly with a second cameraCamera 2 is a second camera, made for the Stick Cam. Switch it on under Cameras, then choose whether it follows Camera 1 or records on its own AUX switch.GoProSet up automatic wake, the GoPro beeper, radio presets, HiLight and the GoPro clock.Keep the GoPro off while the quad stays poweredTurn Auto wake off when you deliberately want the GoPro to stay switched off while CAMLINK and the quad remain powered.Let the GoPro beep with the droneBeep with the drone is on by default. While the quad is disarmed and nothing records, the GoPro beeps along with the quad's beeper.Change the shot without landingSwitch between prepared camera settings in flight, for example 25 fps B-roll and 200 fps slow motion on a camera that supports them. Each GoPro keeps its own saved switch assignments.Assign your preset switchAssign a three-position radio switch so Low, Mid and High can each load a different GoPro preset.Mark a momentOptional bookmarks for long GoPro clips. Mark a moment from the radio so you have a reference when reviewing the footage later.Set the date and time on a naked GoProUse GPS time sync when a naked GoPro does not keep the correct clock between packs. It sets the date and time on your clips, not frame-accurate timecode.Camera 2 has to be on first. Open Cameras and switch it on.On your own CAMLINK, Remove clears only the Camera 2 pairing. Here, you can inspect it without changing a device.Match your radioAdvanced adjustment of CAMLINK's shared Low, Mid and High ranges. The defaults normally work with your radio.Put the information where you want itAdd a field or move it, then see the same change in the OSD.Choose each lineSelect what belongs on lines 1 to 4; unsupported camera values stay blank.Watch the camera batterySet when the camera-battery heads-up appears.Choose what appears in your goggles and where it belongs.Open OSD to edit the four lines.Select line 4. Changes now apply to this line.Tap ASPECT twice, then CAM twice. Line 4 is now free for the preset name.Add Preset to line 4. The example preset name is 25FPS; your real GoPro supplies its own names.On line 2, drag the remaining recording time before the battery. The order here is the order in your goggles.Line 4 shows the example preset name, 25FPS. Line 2 shows recording time left before camera battery. The layout saves automatically.The OSD stays empty until placement is verified. Then it shows the Setup Mode information.Verified. The four Setup Mode lines now appear at the bottom left.OSD after leaving Setup Mode.The LED becomes steadily lit after you hold button 2 for one second. Hold button 2 for three seconds in total to enter Setup Mode. Releasing earlier counts as a short press.Set up CAMLINK, check your first recording and use Link Pause when you fly without a camera.Set up CAMLINK and check the recordingComplete the setup and recording check. Step 7 shows how to fly without a camera.Your first setup is complete. The topics below cover optional settings and the details behind what you see in the goggles.Camera warningsCard, mode and recording warnings are always on. You set two thresholds and decide whether the heads-ups show.Too hot: shows when the camera reports overheating. GoPro, DJI and Insta360 report it.SD card missing and SD card full: catch a camera that cannot record to its card.Too cold: see when a GoPro reports that it is too cold to record. GoPro only.Wrong mode: catch a camera left in photo or timelapse mode before you expect normal video.CAMLINK can only show a warning when the camera reports that condition. The available warnings depend on your camera.Warnings are off by default. The recommended switches are listed above.Camera not in video mode is always on: <code>CHK</code> and <code>!WRONG MODE</code> appear when the camera is set to photo, timelapse or another non-video mode. Switch back to video before flying so you get the footage you intended.A missing or full card prevents the camera from recording to it. These warnings catch a problem you may not see once the camera is mounted.Temperature warnings report a camera condition; they do not prevent a temperature-related failure. <code>!CAM HOT</code> can appear while recording continues. If a clip stops, check cooling and whether the mount covers too much of the camera. Too hot is reported by GoPro, DJI and Insta360; too cold by GoPro only.The factory setting and our recommendation for normal flights. Arming requests recording; disarming starts the selected stop delay.Use Switch when recording should have its own radio switch. The assigned position records; leaving that position requests an immediate stop. Arming and disarming do not control recording in this mode.Use Button for a momentary radio control without arm/disarm automation. Press to start, release, then press again to stop a take. Direct stop commands skip Stop delay.Combi is our preferred option for manual takes in flight. Arming starts recording; a momentary radio button lets you stop and start again without landing. On a RadioMaster Boxer, SF is a good choice. Assign it to an AUX channel and confirm which channel moves in the learner. A deliberate button stop while armed stays stopped until another press or a new arm cycle. A press during the disarm countdown cancels the pending stop and keeps recording.Stop delay: time to re-armWe recommend five seconds, adjustable from zero to thirty. After a crash, disarm and recover the quad. If you re-arm before the countdown ends, the stop is cancelled and the same recording continues.Stop delay applies after disarming in Arm and Combi when Auto stop on disarm is on. A direct stop command from a radio switch or button skips it.Set the clock on a naked GoProA naked GoPro may lose the correct date and time when power is removed. GPS time sync sets its clock after connecting, using flight-controller GPS time and your timezone offset. It needs a valid GPS fix and is off by default. If your camera already keeps the correct clock, you may not need it.CAMLINK reads the camera clock back before showing <code>TIME SYNCED</code>. The <code>TC</code> field then confirms clock sync for the rest of that connection. This sets date and time, not frame-accurate timecode or synchronization between cameras. GPS time sync works on Camera 1 only.Enable GPS time sync, then use Use my timezone as the simplest way to set the offset. Check it again after travel or a daylight-saving change. The stored offset does not update itself.Get help with your CAMLINKEmail <a href="mailto:info@itsfpv.net">info@itsfpv.net</a> and tell us what happened, which camera you use and what the OSD shows. Include the diagnostics file so we can investigate the device’s state and settings.In Setup Mode, open Device → Diagnostics, select Download diagnostics file and attach that file to your email. Download it from your own CAMLINK; the guide only shows the process.If we confirm a firmware bug, we will address it in a firmware update.Firmware updatesFirmware updates<a href="#updates">Firmware updates</a>Check what changed. Update when a release adds a feature you need or fixes a problem that affects you.Current versionReleasedWhat changedDownload .camfwCopied. Paste the guide into your AI chat.The guide could not be copied. Please try again.Fly without the action camProps off, USB unplugged, quad powered by LiPo. Disconnect the configurator before this test. Arm the quad and check that the camera records and REC appears in the goggles.Set up CAMLINK and check recording. Step 7 covers flying without a camera.Recording controlDownload will appear here when the package is available.Camera ready? Short-press button 1 on CAMLINK. Pairing is open for 30 seconds and the LED blinks violet while it runs. If it is already blinking violet, leave it running: another press cancels pairing.To use another supported GoPro, DJI Osmo, Blackmagic, Sony or Insta360, follow the pairing steps for that camera. There is no camera-brand setting to change. Button 1 pairs Camera 1, and a successful new pairing replaces it, so pair again when you switch back. A second camera goes to <a href="#camera-2">Camera 2</a>.Swipe down on the GoPro, swipe left to the last screen and tap Connect Device. Leave that screen open. No touchscreen? Use the <a href="#gopro-naked">GoPro Labs QR code below</a>.Leave Connect Device open while CAMLINK pairs.With GoPro Labs installed, point the camera at this QR code and press the shutter three times quickly. The GoPro is now ready to pair with CAMLINK.Switch the camera on and keep it awake. DJI has no pairing menu to open. When the connection request appears, check the code and approve it on the camera.If CAMLINK’s pairing window is not already open, press button 1. The OSD reads <code>PAIR <NAME></code>, then <code>ROLL R = GET PIN</code>.Leave the Sony pairing screen open while CAMLINK pairs.When the OSD shows <code>ACCEPT ON CAM</code>, approve CAMLINK on the camera.First retail release.1 · trim exposed strandsSide cutters trimming only the exposed wire strands at the CAMLINK end to the length of the solder padsTrim only the exposed strands at the CAMLINK end so they are no longer than the solder pad. Longer strands can touch adjacent pads and cause a short circuit.Choosing a camera under Before You Fly is optional and only shows which functions your model supports. You pair your camera in Step 5.CAMLINK remembers presets and switch mappings separately for each GoPro.Set the preset-switch mapping once for each GoPro. CAMLINK keeps a separate profile for up to four GoPros, with each camera’s presets and mapping. Switching to DJI or another brand keeps these profiles. Pair a remembered GoPro again and its saved mapping is available again. A GoPro paired as Camera 2 does not use presets. Adding a fifth GoPro removes an older profile, prioritising one without a switch mapping.Each line fits 16 characters. Longer text is cut off.Values your camera does not report stay blank. <a href="#cameras">Check your camera’s OSD values.</a>Warnings can briefly replace line 1, and status messages line 2. Searching and pairing screens replace your tokens until they finish.Your radio must be on and connected to the quad. Move the switch you want to assign.Open Recording to assign the switch that will control recording.Open GoPro to assign a switch for changing presets.Choose Switch. The assigned switch position will start and stop recording independently of arming.Turn on Preset switch to assign your three-position radio switch.Open channel selection. The bars show the live AUX input reaching CAMLINK from the flight controller.Move the switch. CAMLINK highlights the AUX channel with the largest change.Tap the highlighted channel to assign it.Move the same switch again. Check that the selected channel follows its movement.Choose High as the recording range. High records; moving out of High stops immediately.Turn on Preset switch so your radio can load the assigned GoPro presets.Open the preset assignments for this camera. Each switch position gets its own preset.Move the switch to Low. CAMLINK loads the preset assigned to Low.Move the switch to Mid and leave it there briefly. CAMLINK loads the middle preset.Move the switch to High. CAMLINK loads the preset assigned to High.Choose Apply and restart to change the shot during recording. It splits the clip, confirms the new preset and starts a new take if recording is still requested. Ignore leaves the current take uninterrupted.Open Diagnostics on the Device page to prepare information for support.Use Download diagnostics file with your own CAMLINK, then email the downloaded file to info@itsfpv.net. Here we only show the control.The diagnostics file is encrypted for it's FPV support. Your Setup Wi-Fi password is redacted from the settings report.These ranges are shared by recording, preset switching, HiLight and the Camera 2 channel. They are not a separate calibration for each AUX channel. Keep the defaults unless needed; turning Custom AUX bands off restores them.Warnings are off by default. Turn on the supported warnings: SD card missing or full, Camera not in video mode, Camera too hot and, on GoPro, Camera too cold. Missing and full card share one switch.Missing and full recording storage share one switch in Setup Mode.After choosing the file, tap Flash. Keep the page open and CAMLINK powered until the update finishes.Package checks and recoveryButtons and OSDWatch the sequence, or press a board button yourself.Your turn. Try any control.Secure the cased module to the mount with the M2 screw. Tighten only until the case is secure and both buttons still click freely. Overtightening can jam the buttons.Case secure, both buttons still clicking freely.Start demoTake controlWatch againPress a board button to take control.Recording. Disarm with the quad switch to stop.Camera connected. Arm the quad to start recording.Arm quadDisarm quadExample: Mission 1 Pro. Arming starts recording. Click “Arm quad” to try it yourself.See setup stepsStop delay gives you time to recover after a crash without ending the clip immediately.Open Recording to find Stop delay.Keep Stop delay at the recommended 5 seconds. You can adjust it from 0–30 seconds.Disarming starts the countdown. Re-arm before it ends and CAMLINK cancels the pending stop, so the same clip continues.The camera confirms recording. The same clip continues while you recover.Disarmed. Stop delay is counting down while the camera keeps recording.The camera confirms that recording stopped. Check this before unplugging power.The camera confirms recording. This is the clip you want to keep through recovery.Disarmed after a crash. The five-second stop delay gives you time to re-arm.Re-armed before the countdown ended. The stop is cancelled and the same clip continues.Disarmed after landing. Wait for the camera-confirmed stop before unplugging power.Stop requested. Wait for the camera to confirm that recording has ended.The camera confirms the stop. The recording has ended.Disarming starts Stop delay, five seconds by default. Wait for the camera to confirm the stop before unplugging power.Arm is the factory setting and the simplest starting point: arming requests recording, and disarming starts the stop-delay countdown.During Stop delay, the timer shows both elapsed recording time and the remaining delay. <code>3:24 5S</code> means a 3:24 clip with five seconds until the stop request. <code>STP</code> is a stop in progress, not confirmation that recording has ended.Wait for the camera-confirmed stop before disconnecting power. If CAMLINK loses power during the countdown, it cannot send the stop command. A camera with its own battery may keep recording; cutting power to the camera itself can lose the unfinished clip.Arm and Combi let you set Auto record on arm and Auto stop on disarm separately. Keep both on for normal flights. Stop on disarm off is a niche choice for keeping the camera rolling on the ground or after a crash; stop the clip yourself at the camera or, in Combi, with the assigned radio button.Keep Stop delay at five seconds unless you need a different recovery window. Re-arming cancels the countdown in Arm and Combi.Stop delay applies after disarming, with Auto stop on disarm enabled. Direct radio stop commands skip it. In Combi, a button press during the disarm countdown cancels that pending stop and keeps the recording going.Change the shot without landingSwitch between prepared presets in flight, for example 25 fps for B-roll and 200 fps for slow motion, if your camera supports them. No landing or camera handling needed. Assign the two presets to Low and Mid; High is optional.Ignore is the default during recording. It leaves the current clip uninterrupted and loads the selected preset once recording stops.Enable Apply and restart when changing the shot mid-flight matters more than keeping one file. CAMLINK waits for a confirmed stop, loads the preset and starts a new clip if recording is still requested.Available frame rates, resolutions and burst durations depend on the camera. Check those limits before building a slow-motion preset; burst modes are not the same as continuous high-frame-rate recording.Create and name presets on the GoPro before flying. Prepare exposure, frame rate, resolution and framing in each one. CAMLINK reads them when it connects and lists them in Setup Mode. Before that first connection, the presets show Not loaded yet.Prepare exposure for each preset before flying. Check shutter, ISO and the ND filter you will use: an exposure that works at 25 fps may not suit 200 fps.Use short, recognizable preset names so you can check the next shot in the goggles. The OSD <code>PRESET</code> field shows up to 12 characters.The camera reports overheating while recording may continue. Check REC as well; the temperature message adds context if the clip stops.The GoPro reports that it is too cold. Check the camera when a recording will not start.Camera battery low and Recording time low are heads-ups with a threshold you set: battery at 5 to 30 percent (default 10), recording time at 1 to 30 minutes (default 5). Each stays quiet while the matching value is already on your OSD.Check the camera and plan the next shotOn the way back, check camera battery and recording time left to decide whether you need a battery or card change. Format and preset fields help you check the next shot before committing to it. Values your camera does not report stay blank.{value} is the camera's battery charge. Check it on the way back to plan the next take; it is separate from the quad's battery.{value} is the estimated recording time that still fits on the camera's storage at its current settings. Check whether there is room for your next take.Auto wake is on by default. Powering the quad lets CAMLINK wake the paired GoPro automatically.Turn Auto wake off to keep the GoPro off while the quad stays powered. Switch the camera on yourself when you are ready. The OSD shows <code>OFF</code> while the camera is off.On supported GoPros, HiLight marks a moment in the current clip so you can find it later. Assign a dedicated momentary radio button. <code>HILIGHT SAVED</code> confirms the camera saved the marker. Your viewing or editing software must support GoPro HiLight markers.CAMLINK talks to the flight controller at 115200 baud only. Set the MSP port in Betaflight to 115200.<code>25FPS</code>After the sixth digit, roll right to <code>>OK<</code>. Roll right again or stay there for one second to send. Roll left to edit.Arming cancels pairing. Losing the RC link for five seconds or briefly pressing either CAMLINK button also cancels it.With Auto record on arm enabled in Arm or Combi, CAMLINK also requests recording after a late connection or reconnection while armed. Retries while the same recording demand stays active are spaced at least 20 seconds apart. In Combi, a manual stop lasts until the next button press or a new arm cycle.Turn your radio on and connect it to the quad. The channel picker shows the live AUX input reaching CAMLINK. Move your switch, then tap the highlighted channel. Move it again to check the assignment.Disarm and stop any recording. Short-press button 2: CAMLINK disconnects the Bluetooth camera link, stops searching for action cams and hides its four OSD lines. Your flight data stays visible.The LED turns white. The Bluetooth camera connection and search are paused, and the four CAMLINK OSD lines are hidden. The rest of your OSD stays visible.Your paired camera stays saved. Link Pause also stays on after a pack change.Disarm and short-press button 2 again to reconnect to your saved camera. You do not need to pair again. Check the camera status in the goggles before arming.Short-press button 2 to disconnect the Bluetooth camera link, stop searching and hide the four CAMLINK lines. Your paired camera stays saved.CAMLINK is not connected to or searching for action cams. The LED is white and its four OSD lines are hidden. Short-press button 2 again to reconnect.CAMLINK searches for your saved camera and reconnects when it is available. Its OSD lines return. No new pairing is needed.The Bluetooth camera connection and search are paused. The four CAMLINK lines are hidden; flight data stays visible. Short-press button 2 again to reconnect to your saved camera.The Bluetooth camera connection and search stay paused. The four CAMLINK lines stay hidden; flight data stays visible. Disarm, then short-press button 2 to reconnect.The Bluetooth camera connection and search are paused. The four CAMLINK lines are hidden; flight data stays visible. Short-press button 2 again to reconnect to your saved camera.The Bluetooth camera connection and search are paused, and the four CAMLINK lines are hidden. Your paired camera stays saved. Short-press button 2 to reconnect.White means the Bluetooth camera connection and search are paused. The four CAMLINK lines are hidden. Short-press button 2 again to reconnect to your saved camera.Is the LED solid white? Link Pause is on. <a href="#link-pause">Resume camera use in step 7</a>.See <a href="#link-pause">A pack without the action cam in step 7</a> for pausing, what the LED and goggles show, and resuming camera use.CAMLINK retains both paired cameras, GoPro mappings, OSD layout and settings when power is disconnected. For Link Pause after a pack change, see <a href="#link-pause">step 7</a>. A factory reset erases the stored settings and camera data.<strong>One free UART.</strong> Check your flight controller’s pinout and serial-port configuration before soldering. A pad and a connector can share the same UART. Do not use a port already assigned to your video system or another device.Mount CAMLINK near the camera, with the LED visible and both buttons accessible. Use the Camera Cage mount on an ERA frame or the standoff mount on a round 5 mm standoff.Place the button cap in the lid, insert the board and fold the case closed. Stack the four wires through the left opening.If the OSD is blank, check Device. Flight controller reads <code>Connected</code> when CAMLINK receives valid MSP data and <code>Silent</code> when it does not. Active wiring shows the RX/TX direction in use, or <code>Searching</code> while CAMLINK is still finding it.Drag tokens onto a line, reorder them or drag them back to the shelf to remove them. The camera state always stays on the layout; you can move it, not remove it. With Camera 2 on, its token starts at line 4, and you can move it like any other token. On a phone, hold a token before dragging. The editor reserves each token's maximum width. Keep each line within 16 characters to avoid text being cut off.The camera has not confirmed the value or does not support it. Sony supplies fewer values; exposure data is Blackmagic only. Check the <a href="#osd">token reference</a> or the <a href="#cameras">model list</a>. If Sony was already recording when CAMLINK connected, the timer stays blank for that clip.During RC failsafe, Switch mode ignores the AUX position the flight controller reports, so recording keeps its last state. Button, Combi and HiLight also ignore AUX changes during failsafe. The preset switch follows the AUX position reported during failsafe.For night flights, reduce the LED brightness under Device: Night 5%, Dim 25%, Day 100%. This also dims warning colors. The LED cannot be switched off.Set DJI Auto Power Off to its highest value. Osmo Nano allows 30 minutes, with no Never option. CAMLINK cannot override this timer or wake DJI cameras. Interaction and recording reset the timer, but an idle camera may switch off before takeoff.A sleeping Osmo Nano shows <code>OFF</code>. Press the camera button to reconnect. Wake it before pairing too. Auto wake is GoPro-only.The camera no longer accepts the saved CAMLINK pairing. Line 2 reads <code>REMOVE IN SETUP</code>: remove it under Cameras in Setup Mode, then leave Setup Mode and pair again.Choose the setting or problem you want help with.Under Corner, choose Bottom left.Greyed-out values stay blank because the camera does not report them. Data: {version}.Check the small blue power LED on the back of CAMLINK. It stays on while the board is powered; it is separate from the front status LED. If it is off, disconnect LiPo and USB, then check the 5 V supply, GND, polarity and solder joints.Check pads and connectors in the FC pinout. An apparently unused pad can share a UART with a plug, such as the one for an air unit. Choose a free port. In Betaflight enable MSP at 115200; in KISS Ultra select MSP Protocol on that serial port. Save, reboot, reconnect and check that the setting stayed.Check the rear blue power LED first. If it is off, disconnect LiPo and USB and check 5 V, GND, polarity and soldering. Disarm and stop recording so the buttons are enabled. Hold button 2 for three seconds; the front status LED turns solid magenta. Wait a few seconds for the Wi-Fi network to appear.Firmware 1.1.0.b2 (beta) · revision 2026-10-19 · about 30 minutes · soldering required · a phone or a laptopPress button 1 or 2 once to leave Setup Mode. CAMLINK restarts. Then pair your camera in Step 5.Shows the instructions for your camera. <button type="button" class="ifg__pick-reset" data-cam-set="">Show all cameras</button>BlackmagicRequires camera firmware 8.1 or newer. Switch Bluetooth on in the camera menu. Turn on your transmitter and connect it to the quad. You will enter the camera's PIN with the sticks while watching the OSD.The camera's PIN window lasts about 30 seconds. Read the code and enter it before the OSD countdown ends.At <code>ROLL R = GET PIN</code>, roll right when ready. This requests the code and starts the timed PIN entry.Read the six digits on the camera. The OSD shows <code>PIN _ _ _ _ _ _</code> and the remaining time.SonyEnable Bluetooth Function and Bluetooth Rmt Ctrl. Open the camera's Pairing screen and leave it open.Prepare the selected camera as shown above, then short-press button 1. The LED blinks violet while pairing.The LED blinks violet. CAMLINK is waiting for the selected camera. Confirm on the camera if asked.The example {camera} is pairing. On your camera, approve the connection if prompted.The pairing window closed. Keep your camera ready and short-press button 1 to try again.Roll right to request the camera's PIN. Its window lasts about 30 seconds. Use the stick below or your arrow keys.Enter the camera's six digits before the OSD countdown ends. Pitch changes the digit; roll moves on. Hold pitch to count faster.PIN sent. Waiting for the camera to confirm pairing.Time ran out. Press button 1, then roll right to request a new PIN.An amber status LED tells you to check the OSD for a problem. The small blue LED on the back only confirms power. During an ordinary warning, a camera that is recording keeps the red recording LED.CAMLINK checks starts and stops against the camera’s recording state. <code>!REC FAILED</code> means a start failed, <code>!NOT STOPPED</code> means a stop failed, and <code>!REC UNKNOWN</code> means the recording state is still unknown.GoPro Labs pairing QR code, command !PRBetaflight OSD set up: lines Enabled and placed, VerifiedGoPro New Mode screen: choose icon and custom nameGoPro Mode Options: Edit Name and Icon, Duplicate Mode, Delete ModeGoggle view of the CAMLINK PIN entry: PAIR FPV, PIN half typed, PITCH=DIGIT, ROLL=NEXT with countdownExample OSD: four lines reading REC 3:24, 85 percent 1H50M, 5.3K 25 LOG, GP13 8:7Recording page with trigger mode selector and stop delayBefore You Fly with the Betaflight OSD group: corner choice and the Set up buttonGoggle view with the four CAMLINK lines showing the Setup Mode screen: network name, SETUP MODE, 10.0.0.1 and firmware versionThe tools for a CAMLINK install: solder, lighter, fine-tip soldering iron, 1.3 mm hex driver and side cuttersEverything in the CAMLINK box: module, harness, heatshrink, Camera Cage mount, standoff mount, button cap and M2 screwThe four joints on the flight controller: white on T5, yellow on R5, black on G, red on 5VNo camera paired<code>!SD FULL</code>: DJI Action 4 to 6 report free space, not a separate missing-card state. Blackmagic and Sony report a full medium when remaining recording time reaches zero.<code>!CAM COLD</code>: GoPro only.New Mode: pick the icon, then the name.Your goggles at the same moment: pitch changes the digit, roll moves on.4-wire silicone harness: 5 V, GND, TX, RXBefore You Fly, CAMLINK lines: choose Bottom left, then Set up.In order of likelihood:GoPro: it has to be in its own pairing menu. If a GoPro you used before refuses to reconnect, remove it on the Cameras page in Setup Mode and pair it fresh.For the case: all four wires exit left, stacked one above another.Naked GoPro: pair by QR codeRequirements: Betaflight 2025.12+ or KISS Ultra B67+, one free UART, 5 V and GND. KISS Ultra uses MSP Protocol on the wired serial port and manually placed Custom Text 1–4. CAMLINK’s automatic OSD placement is Betaflight-only. Setup Mode serves settings at 10.0.0.1 over CAMLINK Wi-Fi; no app or account is needed.Only one device can connect at a time. Turn Wi-Fi off on any other phone or computer connected to CAMLINK. If it disappeared without disconnecting, its slot may remain occupied for about 60 seconds. Default password: itsfpv1234.Prefer watching? The companion video covers this whole page on a real build.Which camera are you flying?If your camera is not in the list, CAMLINK does not support it. That covers Blackmagic bodies without Bluetooth camera control, Sony bodies without a Bluetooth remote, the Osmo Pocket models, and the Insta360 X3, X4 and X5. Blackmagic below camera firmware 8.1 is unsupported: Bluetooth record stop fails on 7.9.x.Press either button to leave Setup Mode. CAMLINK restarts and the OSD shows <code>REBOOTING</code>, then <code>FLIGHT MODE</code>. Most changes are saved automatically: the top right reads <code>Live</code> when device data is fresh and <code>Saved</code> when your last change is stored. Wi-Fi changes require you to tap Save.Solder the four harness wires to CAMLINK. Hold the board with the CAMLINK label upright; the pads are 5 V, GND, TX and RX from left to right.Blackmagic: you need a powered FC, a working RC link and camera firmware 8.1. Roll right to start, then pitch and roll to enter the digits. <a href="#pairing">Full procedure.</a>Disconnect the LiPo and USB before soldering to the flight controller. Solder that end last, once the run is routed and trimmed to length: red to 5 V, black to GND, and the data pair crossed, yellow onto the UART's RX pad, white onto its TX pad.<button type="button" class="link ifg__ai" data-copy-guide hidden>Rather ask your AI? This copies the whole guide as text.</button>For an older release, use its signed .camfw package. CAMLINK checks whether it can be installed and explains any rejection. Retail modules cannot be flashed by cable.<strong>A supported camera.</strong> Verified on our bench: GoPro HERO 11 and 13, MAX 2, Mission 1 Pro; DJI Osmo Nano, Action 2, 4, 5 Pro and 6, Osmo 360 and 360 II; Blackmagic Pocket 4K and 6K; Sony ZV-E10 II and ZV-E1; Insta360 GO Ultra. Other models are expected to work but have not been on our bench. Check your exact camera model in <a href="#cameras">the model picker</a>.After installation, Silent usually means MSP is off on that UART, the port is not set to 115200, the wires sit on a different UART, or GND is missing. CAMLINK finds the RX/TX direction itself. Degraded means the link was working and MSP replies are now failing, so check TX, RX and GND before anything else.The 16-character cut, live: the preset named 8K25 169 ends as 8K25 16.Read the colour and the pattern together: steady, breathing or blinking.A new warning flashes twice on line 1, one second on, one second back to your tokens. When you arm, every warning still standing flashes twice again. Warnings that put the footage at risk then come back as one flash every 10 seconds until fixed; when several stand, they take turns, the most serious first. Heads-ups never repeat.Props off, quad disarmed, battery in. Use a LiPo for this test unless you know that your flight controller powers CAMLINK and the video system from USB. Fresh from the install the LED sits solid amber: powered, but not ready.Trigger modes, stop delay, confirmed camera state<code>!CAM HOT</code>: GoPro, DJI and Insta360.Line rolesOn Sony, the SD token shows only <code>NO SD</code> or <code>FULL</code>, and <code>!WRONG MODE</code> appears when the body is set to stills.Here on UART 5: white to T5, yellow to R5, black to G, red to 5 V.PROFILE is blank on the Mission generation: those cameras have no color-profile setting.Before arming: the LED is solid green and the OSD shows live values, not <code>SEARCHING</code>.Solid green before arming: linked to the camera and the FC.On the GoPro: duplicate a mode or edit its name.Want the lines somewhere else entirely? Place them by hand: <a href="#betaflight">Betaflight</a>.By default, arming requests recording and disarming starts the stop delay. CAMLINK displays camera-confirmed recording state and available telemetry in the goggles. It reads radio inputs for camera controls; it does not control motors, flight stabilization or PID settings.Ports tab: enable MSP on the UART you soldered to, leave the baud at 115200 and every other row unchanged, then save and reboot.Done: CAMLINK is connected to this camera.Already installed and something is not working? <a href="#troubleshooting">Skip to Troubleshooting.</a>Most pilots never open this tab: Before You Fly enables and places the four Custom Message elements for you. Do it by hand when you want them somewhere other than the two offered corners, or when the automatic setup reports Unverified.Place Custom Message 1 at the top, followed by 2, 3 and 4. Horizontal position is yours: on analog the right side has no reserved DJI goggle elements, so the right corners are open too. Enable all four elements so additional CAMLINK lines can be used later without reopening the Configurator.CAMLINK cannot wake a sleeping DJI camera. Switch it on by hand. When an Osmo Nano shows OFF, press its button to reconnect.With Link Pause off, card, camera-mode and recording faults always show, and so does camera-connection status. Only the four heads-ups can be muted, together, with the Heads-up warnings switch.Done: Connected device CAMLINK.Updates ship as signed <code>.camfw</code> packages and install over the Setup Mode Wi-Fi: Device → Firmware Update. A raw <code>.bin</code> is refused, and so is a package built for a different device.After arming: the OSD flips to <code>REC</code> with a running timer and the LED blinks red.A camera on its own battery records independently of CAMLINK: cut CAMLINK's power and the camera keeps rolling until you stop it at the camera. A camera powered from the quad loses power with the pack.Link Pause: fly without the cameraThis guide uses Bottom left, matching the goggle photo. That option becomes available once CAMLINK detects the OSD dimensions from the flight controller. Top left is also available; choose a corner that is free. The right side is not offered.Props off, USB unplugged, quad on its pack: Betaflight blocks arming while the Configurator is connected.The Detailed preset on a HERO 13: recording for 3:24, camera at 85% with 1 h 50 m of card left, 5.3K at 25 fps in LOG, 8:7 aspect.CAMLINK stopped during startup and is waiting for a manual restart: the goggles read <code>PRESS ANY BUTTON</code>, and pressing either button reboots it. If it keeps coming back, send us the diagnostics file.If the LED is white, <a href="#link-pause">turn Link Pause off with button 2</a> before trying button 1. Pairing runs in Flight Mode with the quad disarmed, recording stopped and the camera close by. Follow the instructions for your camera brand:When the camera should start and stop. Trigger mode, arm and disarm automation, stop delay, Blinking REC, and Camera 2 when it is on. <a href="#recording">Recording in detail.</a>Re-enter Setup Mode and open Warnings. Switch on:A DJI camera stopped sending its status. Old values are hidden. Land if airborne and restart the camera.DJI: the camera has to be on and awake; CAMLINK will not wake it for you. Then approve the prompt on the camera screen. On a Nano or Action 2 you have 30 seconds and the OSD shows you the code.Factory reset: the clean slatePair Camera 1, or replace it after a successful new pairing. Press again during pairing to cancel. With Link Pause on, button 1 is blocked; short-press button 2 to resume first.The stop delay isn't workingA recording start failed. On cameras that report a missing card, no card shows earlier as <code>CHK</code> with <code>!NO SD</code>.Sony: both Bluetooth Function and Bluetooth Rmt Ctrl must be on, and the camera has to be in its pairing screen.What the camera is doing: <code>RDY</code> ready, <code>REC</code> recording, <code>STP</code> stopping or saving, <code>CHK</code> connected but cannot record normally, <code>OFF</code> switched off or asleep<code>!NO SD</code>: GoPro, Blackmagic, Sony, Insta360, and on DJI only the Osmo Nano and Action 2.Action 4 to 6 normally reconnect without another confirmation. If the camera asks again, approve the request.Start in the camera menu: set Auto Power Off to the highest value the camera offers. On a shorter setting it switches itself off between takes, and CAMLINK cannot turn it back on.Pair a cameraPress button 2 briefly to resume the link, then press button 1 to pair a new camera.Pair a camera1 · Pair cameraAmber · no paired cameraButton 1: press and release to pair a camera; hold 3 seconds for Camera 2.1 · Pair cameraHold 3 s: Setup ModeButton 2: short press for Link Pause, hold three seconds for Setup Mode.2 · Press: Link PauseExample: Mission 1 ProButton 2 held for 3 seconds: Setup Mode. Press either button to exit.{value} describes the shape of the recorded image. Blackmagic can show ANAM for an anamorphic format; unreported ratios stay blank.{value} shows how long this clip has been recording. During a stop delay, the extra S value counts down to the stop request.{value} is free recording space; G means gigabytes and M means megabytes. NO SD means no card and FULL means the card is full. Sony and Blackmagic show only NO SD and FULL. If the camera uses internal storage, this value refers to that storage.{value} is the shutter angle reported by Blackmagic; D means degrees. The field stays blank when the camera does not report an angle.{value} is the camera’s state: RDY means ready, REC means confirmed recording, STP means it is stopping or saving, CHK means it is connected but cannot record normally, and OFF means it reports that it is off or asleep.The stop is finishing. Keep power connected until the camera confirms that recording has stopped.Pair cameraButton 1: pairing. The prepared Mission 1 Pro will connect shortly. Press again to cancel.A pack without the camera? Short-press button 2.Pair a cameraAdd SD card to show the remaining card space; the change saves automatically.Line 4 now shows M1P and 108G: Mission 1 Pro with 108 GB free on its card.Leave Heads-up warnings on; each one appears only when the camera reports that condition.Solid white: Link Pause is on.Goggle view with Betaflight battery and flight information visible and all four CAMLINK lines hiddenFlying without the action cam? <a href="#link-pause">Link Pause</a> stops camera searching and hides the CAMLINK lines.Osmo Nano / Action 2: When CONFIRM appears with a code, check that the code matches and approve the connection on the camera within 30 seconds. Once paired, the camera reconnects automatically.Four example OSD lines for {model}. Camera tag: {tag}.Button 2: cancel pairingPitch down: decrease digitPitch up: increase digitRoll left: edit previous digitRoll right: start, next digit or sendChange the stop delayChanges affect this example only. Your OSD fields and stop delay carry over to the board above.Check the four destinations. At the module: red to 5V, black to GND, yellow to TX, white to RX. At the flight controller, TX connects to RX and RX to TX.Flight-controller wiring referenceBetaflight Ports referenceExample Blackmagic code: 378084Pitch down: previous digitPitch up: next digitWhite LED, no CAMLINK lines. Change the example pack to see the pause persist, then short-press button 2 to reconnect.Roll left: previous positionRoll right: next positionModule-side soldering referenceChoose an example camera. Arm and disarm the example quad to see recording and the stop delay. Press button 2 to try Link Pause.Wait for the stop delay and the camera's confirmation. The PCB buttons stay inactive while recording.Already set up? Explore settings and details.Open http://10.0.0.1/ in your browser.Hold button 2 for 3 seconds. The LED turns magenta.Open Before You Fly, then Betaflight OSD. Choose Bottom left, tap Set up, then Confirm setup. Wait for Lines placed.On your phone, join CAMLINK-XXXXXX. Password: itsfpv1234.Example: VELOX F7 SE, UART 5. TX goes to R5; RX goes to T5.Pads from left to right: 5V, GND, TX, RX.Front view of CAMLINK with its logo upright. The four pads at the bottom are labeled 5V, GND, TX and RX from left to right. No wires are shown.Factory reset. The LED shows a rainbow while CAMLINK erases. It then restarts in Flight Mode and the goggles show <code>RESET DONE</code> or <code>!RESET FAILED</code>.Done when all four joints on CAMLINK are clean and no solder bridges adjacent pads.CAMLINK board and an injection-molded polypropylene case, black or transparent. You put the two together in step 2.
Press button 1 or 2 once to leave Setup Mode. CAMLINK restarts. Then pair your camera in Step 5.